Skip to content Skip to sidebar Skip to footer

Xiaomi Pocophone F1 Test Point For Flashing And MIUI Upgrade

Xiaomi Pocophone F1 Test Point For Flashing And MIUI Upgrade
Xiaomi Pocophone F1 Test Point - in addition to using the EDL mode method to upgrade the MIUI firmware on Xiaomi Poco F1 smartphones, there is one more way you can do that is by the test point method.

By using the test point on the Xiaomi Poco F1 smartphone you do not need to unlock the bootloader first, which can eliminate the warranty status on your smartphone.

And this way is powerful enough to overcome the problem of damage to Xiaomi smartphones such as the following example:

  • Bootloop phones
  • Xiaomi's soft brick mobile phone
  • Xiaomi Pocophone F1 mobile phone that experienced a hard brick.
  • The phone is restarted continuously.

Before we continue the discussion on how to determine the pinout point of Xiaomi Pocophone F1 Test Point and how to use it further you can prepare some materials and tools used to perform the test point method on the Xiaomi Poco F1 smartphone.

Of course, to perform the test point method on Xiaomi mobile devices required materials and supporting tools to maximize the process of flashing and upgrading MIUI by means of test points.

Tools and materials to conduct a Xiaomi PocoPhone F1 test point

1.Pick
You can use the pick to open the back cover of the Xiaomi Poco F1 phone. can use a guitar pick or similar objects.

2. Screwdriver
The mainboard of the Xiaomi phone is certainly covered with plastic or iron material glued using bolts, to remove the cover on the motherboard Xiaomi Poco F1 then required a special screwdriver small size to open the bolt.

3. Tweezers or jumper cables
This tool is used to connect the pinout test point on the Xiaomi PocoPhone f1 phone which will be reinstalled by the software.

4. USB data cable type C
Type C data cable is used to connect the phone that will be repaired software to a PC or laptop.

5. Qualcomm driver
Qualcomm drives are used to detect mobile devices on PCs or laptops. Install Qualcomm drivers on your PC. If your phone is well connected, you will get a status notification "Qualcomm HS-USB QDLoader 9008" that you can check on the devices manager on PCs and laptops.

6. Stock Rom and Miflash tools
Both of these materials must be owned to install on the Xiaomi Pocophone F1 smartphone.

You can find a stock ROM that matches your phone type on the website or blog of Xiaomi phone's firmware stock ROM download provider.

 

After knowing what materials and tools are needed to perform the reinstallation process with the test point method on Xiaomi Poco F1.

Below TestpoinDroid will provide an example image to determine the location of the pinout point Android Pocophone F1.How to do a test point Xiaomi Poco phone F1

Android smartphone Xiaomi Pocophone F1 test point position

After knowing the location of the pin test point on Poco F1 then the next step is how to process the process.

  • As a first step, you can turn off your phone first.
  • Next, connect the two-pin test points using tweezers or jumper cables.
  • Keep connecting those two test point pins and plug the USB type C cable into the charger port on your phone and make sure the Qualcomm HS-USB QDLoader 9008 driver is perfectly installed on PCs and laptops.
  • Next, open the Miflashtools application and do flashing in the usual way.

To avoid failure in the flash process with the test point method, try to use a USB type C data cable in good condition, and battery power on the phone is more than 50%.

that's the information and a short tutorial to determine the location of the Test point pin on the Xiaomi PocoPhone F1 Android smartphone device.

Hopefully, the information about Xiaomi Pocophone F1 Test Point can be useful for all of you. Thanks.

Post a Comment for "Xiaomi Pocophone F1 Test Point For Flashing And MIUI Upgrade"